Aube-technologies TH148LE Manual do Utilizador descarregar pdf

TH147 and TH148LE 400-147-010-C 27/11/06 1/4

The TH147 and TH148LE thermostats can be used to control:

• a gas, fuel oil or electric furnace - 2 or 3 wires

• a central air conditioner - 2 or 3 wires

• a hot water system with or without pump - 2 wires

• a millivolt system - 2 wires

• a central heating and cooling system - 4 or 5 wires

Attention: These thermostats are not compatible with heat pumps

or multi-stage systems.

Note: The installation must be performed by an electrician or a qual-

ified installer.

2.1 Removing the Old Thermostat

IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT

POWER TO THE HEATING/COOLING SYSTEM.

n Remove the old thermostat to access the wires.

Attention: If the old thermostat was mounted onto an electrical box,

it might have been powered by 120/240 volts. In this case, the

TH147 or TH148LE thermostat cannot be used.

o Identify and label each wire (with the corresponding letter on

the wire terminal) and remove it from its terminal.

p If necessary, strip the end of each wire

(maximum of 6 mm).

q Wrap the wires around a pencil to prevent

them from falling into the wall.

r If the hole in the wall is too big, insulate it

using a non-flammable material in order

to avoid air draughts behind the thermostat.

2.2 Installing the New Baseplate

For a new installation, choose a location approximately 1.5 m

(5 feet) above the floor and on an inside wall. Avoid draughty

areas (top of staircase, air outlet, etc.), dead air spots (behind

doors), direct sunlight or areas near concealed pipes or chim-

neys.

n Remove the thermostat faceplate.

o Loosen the locking screw in order to separate the thermostat

from its baseplate (the screw cannot be completely removed).

p Gently tilt the thermostat upwards.

q Mark and bore the appropriate mounting holes (or use the

existing holes). Insert the plastic anchors.

r Pass the wires through the opening of the baseplate and fix the

baseplate to the wall using the screws provided.

1. Introduction

Functions

TH147

TH148LE

Heating/cooling control X X

Fan control X X

Programmable cycle lengths X X

Temperature display in °C or °F X X

Backlit display X X

Battery replacement indicator X X

Unoccupied mode activated remotely (requires Aube’s CT240) X

Interchangeable faceplates (titanium, charcoal & taupe) X

TH147 & TH148LE

Electronic Thermostats

Installation

and User Guide

Display

Adjustment

buttons

System operating

mode selector

Fan operating

mode selector

Backlight

button

2. Installation

400-147-010-C (TH147_TH148 NP Aube) ENG.fm Page 1 Monday, November 27, 2006 10:41 AM

1 2 3 4

Resumo do Conteúdo

Página 1 - 2. Installation

TH147 and TH148LE 400-147-010-C 27/11/06 1/4The TH147 and TH148LE thermostats can be used to control: • a gas, fuel oil or electric furn

Página 2

TH147 and TH148LE 400-147-010-C 27/11/06 2/42.3 Connecting the ThermostatRefer to the following table for matching the wire labels with

Página 3 - 3. Basic Functions

TH147 and TH148LE 400-147-010-C 27/11/06 3/42.6 Installing the Batteriesn Gently pull out the battery cover. o Install the batteries as

Página 4 - 7. Service

TH147 and TH148LE 400-147-010-C 27/11/06 4/4n To access the configuration menu, press the backlight button for 3 seconds.o To go to the

Modelos relacionados TH147

Comentários a estes Manuais

Sem comentários

Aube-technologies TH148LE Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Painel de controlo Aube-technologies TH148LE. Aube Technologies TH148LE User Manual Manual do Utilizador

Resumo do Conteúdo

Modelos relacionados TH147

Comentários a estes Manuais

Manuais e produtos relacionados com Painel de controlo Aube-technologies TH148LE